Description QUICSEAL 105 is a one component water-borne polymeric solution for dampness sealing and waterproofing coating on concrete and masonry substrates. It can be gravity fed into cracks or injected into soil behind substrate.
It is specially blended with inorganic compounds and polymers to achieve both surface and in-depth sealing (by film forming and crystallization). QUICSEAL 105 is UV resistant and provides long-term surface protection. Upon application, a protective film is formed immediately, providing sealing of the surface. Moisture collected behind the surface reacts with the active ingredients in QUICSEAL 105 to increase the concrete pH to greater than 10.
Where there is ground water intrusion, QUICSEAL 105 can be injected into soil behind substrate without relieving water pressure. QUICSEAL 105 will react with ground water and chemical reaction will take place. Colloidal particles will be formed and carried by ground to block all seepage points, up to 3 metre from point of injection.
Advantages
One part, brush or roller application
Seal dampness by both film forming and crystallization
Translucent and UV resistant
Fine hairline cracks sealing
Able to consolidate weak substrates
Paintable with emulsion paint
Suitable for injection with one component pump
Low viscosity a allows sufficient penetration into substrate
Good adhesion to the substrate
Impermeable to water and yet breathable
Uses
Waterproofing of :
Concrete roof - top
Concrete bridge decks
Bricks end-walls
Cement fibreboards
Dampsealing of :
Leaking kitchen and toilet roofs (soffit)
Retaining walls
Basement walls and floors
Tunnels
Cement fibreboard
Interior and exterior walls before painting
Application Instructions
Remove all loose materials by high pressure water jetting. Remove old paint by mechanical means i.e. scrapper, wet grit basting, needle hammer or grinding.
Stop all water leakage point by using QUICSEAL 516 WATERPLUG. Allow substrates to dry until no running or free water is observed.
Stir QUICSEAL 105 for about 1 minute and apply liberally with a brush or roller without ponding. Allow it to dry for about an hour and if substrate is very absorbent, apply a second coat.
Subsequent Finishes
If subsequent is desired, the general recommendation is as follows:
Painting: A good quality acrylic based emulsion can be applied onto dried QUICSEAL 105 MAGICSEAL after at least 4 hours of drying.
Waterproofing membrane: Where desired, liquid applied water-borne membranes can be applied over QUICSEAL 105, after surface dry to improve adhesion.
Technical Information
Form
white liquid
Flash Point
not flammable
Solid Content
> 32%
Density
1.17 ± 0.04
Water Vapour Transmission
> 60% reduction after treatment
Application Temperature
5°C to 60°C
Drying Time
<1 hour at 25°C, 65% RH
Weathering (outdoor exposure – 168 hours)
no cracking
Chemical Resistance (Spot Test)
i. NaOH
ii. Ca(OH) 2
iii. 0.2% HCI
no cracking, no blistering
Depth of Absorption
1mm to 8mm (grade 20 concrete)
Application Rate
12 to 16m2/kg
Storage Life
12 months in original unopened container
Packing Size
5kg, 20kg and 200kg
Cleaning
Clean tools with fresh water immediately after use. Glazed surfaces should be cleaned immediately on contact with fresh water to retain its original gloss.
Health & Safety
Under normal use, this product will not exhibit health hazard. Good hygiene practice must be observed. Wear protective gloves and eye goggles while working. Wash hands thoroughly before eating and drinking.
Important Notes
The information set forth herein is furnished in good faith and is based on technical data that QUICSEAL considers to be reliable. This information is intended for used by persons having technical skill and at their own discretion and risk. Information contained in this product sheet conforms to the standard detail recommendations and specifications for the installation of QUICSEAL products as of the date of publication of this document. QUICSEAL makes no other warranties and assumes no liability, expressed or implied, as to the architecture, engineering or workmanship of any project. To ensure that you are using the latest, most complete information, contact QUICSEAL Reference No.: QS 105/220520
Unlimited Blocks, Tabs or Accordions with any HTML content can be assigned to any individual product or to certain groups of products, like entire categories, brands, products with specific options, attributes, price range, etc. You can indicate any criteria via the advanced product assignment mechanism and only those products matching your criteria will display the modules.
Also, any module can be selectively activated per device (desktop/tablet/phone), customer login status and other criteria. Imagine the possibilities.
